Skip to main content

RF PCB Routing Guidelines and Essentials

RF module on a PCB layout background


In the world of electronics, RF (Radio Frequency) signals play a crucial role in various applications, from wireless communication to radar systems. Ensuring proper signal integrity by following RF PCB routing guidelines is essential for achieving optimal performance in RF circuit designs. Frequencies falling in the RF range span from thousands to billions of Hz, and these frequencies are present in a huge number of analog/mixed signal devices. A board does not have to appear in a communication device to be classified as an RF circuit, but many of the same design rules will apply.

RF PCB Routing Guidelines Summary

Guideline

Description

Impedance Matching

Ensure impedance matching between traces, source, and load components for signal integrity.

EMI and Magnetic Fields

Consider EMI from traces/components, susceptibility to magnetic fields, and radiated EMI.

Power-Ground Decoupling

Maintain proper decoupling between power and ground planes.

RF Signal Coupling

Prevent coupling between RF signal traces.

Trace Path Continuity

Avoid sharp angles to remove impedance discontinuities.

Shielding Traces

Use shielding traces for RF signals.

Trace Separation and Clearances

Separate RF traces by predefined clearances on the same and other layers.

Power-Plane and Via Usage

Surround power plane with grounded vias, minimize via usage, use back-drilled vias.

High-Frequency Trace Routing

Keep analog signal traces short, increase separation between traces, avoid parallel routing.

Mixed Signal Considerations

Apply mixed signal design techniques, segment sensitive RF components, and reduce noise coupling.

RF PCB Routing Guidelines: Impedance Matching and Your Layer Stack

Routing your RF board to ensure signal integrity is just as much about designing the right layer stack as it is about laying traces. You can suppress transmission line effects in your signal lines with the right layer stack in your PCB.

While normally discussed in terms of digital signals, signal reflection at an impedance discontinuity affects analog signals when traces operate as transmission lines. When the propagation delay along an interconnect is greater than one-quarter the oscillation period of the analog signal, then transmission line effects become a concern.Therefore, ensuring that your traces are impedance matched is critical.

Although there is some natural attenuation of a reflected signal in an analog signal trace, the analog traces are constantly pumped with a harmonic source, and a reflected signal can form a standing wave in a trace if reflected at an impedance discontinuity. The natural attenuation in the signal trace only dampens the maximum amplitude at resonance, it does not completely eliminate resonance.

Transmission Line Guidelines and the Important of Impedance Matching

Any analog signal resonance on a transmission line can form a standing wave along the trace (depending on the geometry), creating a high amplitude electric field that can induce noise in other areas of the board. You can eliminate this problem if your traces are impedance matched with your source and load components.

To ensure that your traces always remain impedance matched, you should firstly use impedance controlled design within your layer stack. This ensures that traces routed in the signal layers will have a defined value within a specific tolerance. You will only need to worry about matching the impedance of your source and load components to this value. In other words, if one component at the end of an interconnect has different impedance than your signal trace, you must compensate the impedance of the component, rather than the trace itself.

WiFi module with a microcontroller on a small PCB

Ensure your boards can work through the intricacies of proper signaling with strong RF PCB routing guidelines

RF PCB Routing Basic Guidelines

Because the impedance of your traces is so important, your routing techniques should make sure to take the following basic RF PCB routing guidelines into account:

  • EMI from other traces/components, susceptibility to external oscillating magnetic fields, and EMI radiated from your board
  • Decoupling between power and ground
  • Preventing coupling between RF signal traces
  • Anything that can increase the impedance mismatch between traces, sources, and loads
  • Prevent resonances that can radiate strongly into other areas of your board or into external boards
  • Avoid sharp angles of shapes in your trace path to remove discontinuities of impedance
  • Use shielding traces for RF signals
  • Separate the RF traces by predefined clearances on the same layer and other layers

Especially at higher frequencies, RF signals may impact other circuits and could also be susceptible to interferance by other signals. This is why it is important that the RF traces are protected. The key methods include good grounding, shielding and filtering.

Power-Plane, Via Usage, and High Frequency Routing Guidelines

While this is a tall order, you cannot perfectly satisfy every requirement at all times. Which of these points should receive more attention depends on the particular application for your board. While the list of RF PCB routing guidelines is extensive, below are some important guidelines to consider:

To suppress radiation from your circuit to your power nets, you can surround the power plane with grounded vias. It is also a good idea to place the power plane between two ground planes as this will sufficiently decouple the power and ground planes throughout the board.

With higher frequency RF circuits, traces carrying your analog signals will need to be quite short in order to prevent transmission line effects. The separation between lines should be as large as possible, and they should not be routed close together over long distances. Coupling between parallel microstrip traces increases as the parallel routing length increases and the separation distance decreases.

Once you’ve calculated the trace geometry for your given layer stack, try to minimize the use of vias along your traces as each via increases the impedance of your interconnect. Aside from increasing impedance, any stubs left on a via will act as high frequency resonators. Vias should be back-drilled in order to prevent standing waves from forming in the via stub as a resonating signal in a stub can act as a strong radiator or antenna.

If you need to route an RF signal line to a different layer, you can use two vias in parallel to minimize the total additional inductance and impedance. Two vias in parallel will have total impedance and inductance that is half the value of a single via. When you need to place a bend in an RF signal line due to routing constraints, you’ll want to use a bend radius that is at least 3 times the trace width. This will minimize impedance changes that arise from bending a trace.

RF Boards as Mixed Signal Devices

Unless your RF board is part of a multi-board system, your RF PCB is likely to be a mixed signal device. As such, you will need to consider standard mixed signal design techniques in addition to the previously mentioned RF PCB routing guidelines when working with these systems. Some of these devices will include wireless capabilities, so wireless design rules will also play a part in your design process.

With RF devices, you will likely include other analog circuitry on your board that supports your RF components and provides greater functionality. If this is the case, you should try to segment your sensitive RF components from other analog components in order to avoid routing analog return signals below sensitive RF circuit blocks.

You’ll want to follow best practices for mixed signal design, including properly splitting your ground planes, taking care to place mixed signal ICs, and proper arrangement of your analog power and ground sections. Your goal should be to reduce noise in the digital section from coupling into the RF analog section, and vice versa. Pay attention to some basic rules for routing mixed signal PCBs if you are designing this type of board.

Analog chips and components on a PCBs

Maintaining security in your circuit board is vital through strong RF PCB routing guidelines

When it comes to routing RF PCB boards and ensuring optimal signal integrity, using advanced software can significantly streamline the design process and yield superior results. Cadence AWR software stands out as the ultimate tool for RF PCB routing, offering a comprehensive suite of features and capabilities specifically tailored for RF design engineers. Take advantage of Cadence AWR Software to streamline your RF PCB design process, reduce design iterations, and achieve superior signal integrity for your high-frequency circuits.

Leading electronics providers rely on Cadence products to optimize power, space, and energy needs for a wide variety of market applications. To learn more about our innovative solutions, talk to our team of experts or subscribe to our YouTube channel.

Untitled Document